Wolfgang Blum
Wolfgang Blum
Professor, Dr.-Ing. habil., Dr.-Ing., Dipl.-Phys.
Verified email at fau.de
Cited by
Cited by
Transition from strengthening to softening by grain boundaries in ultrafine-grained Cu
YJ Li, XH Zeng, W Blum
Acta Materialia 52 (17), 5009-5018, 2004
Dynamic recovery: sufficient mechanism in the hot deformation of Al (< 99.99)
HJ McQueen, W Blum
Materials Science and Engineering: A 290 (1-2), 95-107, 2000
Geometric dynamic recrystallization in hot torsion of Al 5Mg 0.6 Mn (AA5083)
W Blum, Q Zhu, R Merkel, HJ McQueen
Materials Science and Engineering: A 205 (1-2), 23-30, 1996
Rate dependent constitutive relations based on Anand model for 92.5 Pb5Sn2. 5Ag solder
J Wilde, K Becker, M Thoben, W Blum, T Jupitz, G Wang, ZN Cheng
IEEE transactions on Advanced Packaging 23 (3), 408-414, 2000
Evolution of microstructure and deformation resistance in creep of tempered martensitic 9–12% Cr–2% W–5% Co steels
R Agamennone, W Blum, C Gupta, JK Chakravartty
Acta materialia 54 (11), 3003-3014, 2006
Comparative study of creep of the die-cast Mg-alloys AZ91, AS21, AS41, AM60 and AE42
W Blum, P Zhang, B Watzinger, BV Grossmann, HG Haldenwanger
Materials Science and Engineering: A 319, 735-740, 2001
Development of process maps for plasma spray: case study for molybdenum
S Sampath, X Jiang, A Kulkarni, J Matejicek, DL Gilmore, RA Neiser
Materials Science and Engineering: A 348 (1-2), 54-66, 2003
A simple dislocation model of deformation resistance of ultrafine-grained materials explaining Hall–Petch strengthening and enhanced strain rate sensitivity
W Blum, XH Zeng
Acta Materialia 57 (6), 1966-1974, 2009
Dynamic recovery during and after steady state deformation of Al-11wt% Zn
J Hausselt, W Blum
Acta Metallurgica 24 (11), 1027-1039, 1976
Understanding creep—a review
W Blum, P Eisenlohr, F Breutinger
Metallurgical and Materials Transactions A 33 (2), 291-303, 2002
Temperature dependence of the strength of fine-and ultrafine-grained materials
JH Schneibel, M Heilmaier, W Blum, G Hasemann, ...
Acta materialia 59 (3), 1300-1308, 2011
Two mechanisms of dislocation motion during creep
W Blum, A Rosen, A Cegielska, JL Martin
Acta Metallurgica 37 (9), 2439-2453, 1989
High‐Temperature Deformation and Creep of Crystalline Solids
W Blum
Materials science and technology, 2006
Role of Dislocation Annihilation during Steady‐State Deformation
W Blum
Physica status solidi (b) 45 (2), 561-571, 1971
Martensitic/ferritic super heat-resistant 650 C steels-design and testing of model alloys
V Knezevic, G Sauthoff, J Vilk, G Inden, A Schneider, R Agamennone, ...
ISIJ international 42 (12), 1505-1514, 2002
Long-range internal stresses in cell and subgrain structures of copper during deformation at constant stress
S Straub, W Blum, HJ Maier, T Ungar, A Borbely, H Renner
Acta materialia 44 (11), 4337-4350, 1996
New technique for evaluating long range internal back stresses
W Blum, A Finkel
Acta Metallurgica 30 (8), 1705-1715, 1982
Subgrain formation during deformation: physical origin and consequences
R Sedláček, W Blum, J Kratochvil, S Forest
Metallurgical and Materials Transactions A 33 (2), 319-327, 2002
Creep of Die‐Cast Light‐Weight Mg–Al‐base Alloy AZ91hp
W Blum, B Watzinger, P Zhang
Advanced Engineering Materials 2 (6), 349-355, 2000
On the stress dependence of the stationary deformation rate
W Blum, B Reppich
Acta Metallurgica 17 (8), 959-966, 1969
The system can't perform the operation now. Try again later.
Articles 1–20