Timothy J. Eden
Timothy J. Eden
Applied Research Laboratory, The Pennsylvania State University
Dirección de correo verificada de psu.edu
Título
Citado por
Citado por
Año
The 2016 thermal spray roadmap
A Vardelle, C Moreau, J Akedo, H Ashrafizadeh, CC Berndt, JO Berghaus, ...
Journal of thermal spray technology 25 (8), 1376-1440, 2016
1632016
Mesoscopic structure control of spray formed high strength Al–Zn–Mg–Cu alloys
MM Sharma, MF Amateau, TJ Eden
Acta materialia 53 (10), 2919-2924, 2005
932005
CMAS‐resistant thermal barrier coatings (TBC)
AK Rai, RS Bhattacharya, DE Wolfe, TJ Eden
International Journal of Applied Ceramic Technology 7 (5), 662-674, 2010
882010
Cold spray Al-5% Mg coatings for the corrosion protection of magnesium alloys
BS DeForce, TJ Eden, JK Potter
Journal of Thermal Spray Technology 20 (6), 1352-1358, 2011
842011
On the characterization of bulk copper produced by cold gas dynamic spray processing in as fabricated and annealed conditions
PD Eason, JA Fewkes, SC Kennett, TJ Eden, K Tello, MJ Kaufman, ...
Materials Science and Engineering: A 528 (28), 8174-8178, 2011
692011
Hardening mechanisms of spray formed Al–Zn–Mg–Cu alloys with scandium and other elemental additions
MM Sharma, MF Amateau, TJ Eden
Journal of Alloys and Compounds 416 (1-2), 135-142, 2006
642006
Aging response of Al–Zn–Mg–Cu spray formed alloys and their metal matrix composites
MM Sharma, MF Amateau, TJ Eden
Materials Science and Engineering: A 424 (1-2), 87-96, 2006
642006
Effect of substrate surface roughening and cold spray coating on the fatigue life of AA2024 specimens
CW Ziemian, MM Sharma, BD Bouffard, T Nissley, TJ Eden
Materials & Design (1980-2015) 54, 212-221, 2014
632014
Investigation and characterization of Cr3C2-based wear-resistant coatings applied by the cold spray process
DE Wolfe, TJ Eden, JK Potter, AP Jaroh
Journal of thermal spray technology 15 (3), 400-412, 2006
632006
Amorphous phase formation in spray deposited AlYNiCo and AlYNiCoZr alloys
CRM Afonso, C Bolfarini, CS Kiminami, ND Bassim, MJ Kaufman, ...
Scripta materialia 44 (8-9), 1625-1628, 2001
602001
Amorphous phase formation during spray forming of Al84Y3Ni8Co4Zr1 alloy
CRM Afonso, C Bolfarini, CS Kiminami, ND Bassim, MJ Kaufman, ...
Journal of non-crystalline solids 284 (1-3), 134-138, 2001
512001
Erosion performance and characterization of nanolayer (Ti, Cr) N hard coatings for gas turbine engine compressor blade applications
MW Reedy, TJ Eden, JK Potter, DE Wolfe
Surface and Coatings Technology 206 (2-3), 464-472, 2011
472011
Challenges in the development of aluminium-based bulk amorphous alloys
CS Kiminami, ND Bassim, MJ Kaufman, MF Amateau, TJ Eden, ...
Key Engineering Materials 189, 503-508, 2001
342001
Evaluation of ice-adhesion strength on erosion-resistant materials
J Soltis, J Palacios, T Eden, D Wolfe
AIAA journal 53 (7), 1825-1835, 2015
322015
Effect of surface preparation on the microstructure, adhesion, and tensile properties of cold-sprayed aluminum coatings on AA2024 substrates
MM Sharma, TJ Eden, BT Golesich
Journal of Thermal Spray Technology 24 (3), 410-422, 2015
322015
Energetic intermetallic materials formed by cold spray
SW Dean, JK Potter, RA Yetter, TJ Eden, V Champagne, M Trexler
Intermetallics 43, 121-130, 2013
302013
Fatigue behavior of SiC particulate reinforced spray-formed 7XXX series Al-alloys
MM Sharma, CW Ziemian, TJ Eden
Materials & Design 32 (8-9), 4304-4309, 2011
282011
Self-lubricating cold-sprayed coatings utilizing microscale nickel-encapsulated hexagonal boron nitride
LM Stark, I Smid, AE Segall, TJ Eden, J Potter
Tribology Transactions 55 (5), 624-630, 2012
262012
Application of high-pressure cold spray for an internal bore repair of a navy valve actuator
CA Widener, MJ Carter, OC Ozdemir, RH Hrabe, B Hoiland, TE Stamey, ...
Journal of Thermal Spray Technology 25 (1-2), 193-201, 2016
252016
Combined effect of hot extrusion and heat treatment on the mechanical behavior of 7055 AA processed via spray metal forming
JM Schreiber, ZR Omcikus, TJ Eden, MM Sharma, V Champagne, ...
Journal of alloys and compounds 617, 135-139, 2014
252014
El sistema no puede realizar la operación en estos momentos. Inténtalo de nuevo más tarde.
Artículos 1–20