| Improving tensile properties of kenaf fibers treated with sodium hydroxide MS Meon, MF Othman, H Husain, MF Remeli, MSM Syawal Procedia Engineering 41, 1587-1592, 2012 | 125 | 2012 |
| Influence of fins designs, geometries and conditions on the performance of a plate-fin heat exchanger-experimental perspective MIN Ma’arof, GT Chala, H Husain, MSS Mohamed Journal of Mechanical Engineering and Sciences 13 (1), 4368-4379, 2019 | 7 | 2019 |
| Influence of Cutting Edge Radius in Micromachining AISI D2 JB Saedon, AHA Halim, H Husain, MS Meon, MF Othman Applied Mechanics and Materials 393, 253-258, 2013 | 6 | 2013 |
| Computational model analysis on a bipolar plate flow field design of a PEM fuel cell KI Sainan, R Atan, H Husain, W Mohamed 2011 5th International Power Engineering and Optimization Conference, 133-138, 2011 | 6 | 2011 |
| Influence of machining parameters on surface roughness in WEDM titanium alloy JB Saedon, JR Ding, JR Paul, MSM Shawal, H Husain, MS Meon Advanced Materials Research 701, 349-353, 2013 | 3 | 2013 |
| Investigation of The Amount of Energy Absorption of Aluminium Tube: Inversion and Concertina Collapse Mode MS Meon, H Husain International Journal on Advanced Science, Engineering and Information …, 2012 | 3 | 2012 |
| Potential utilization of biodiesel as alternative fuel for compression ignition engine in Malaysia MA Wahab, MIN Ma’arof, IN Ahmad, H Husain IOP Conf. Ser. Mater. Sci. Eng 257 (1), 543-687, 2017 | 2 | 2017 |
| Compressive mechanical properties of porous TI-6AL-4V with palm stearin binder system NHM Nor, JB Saedon, NAA Kasim, MH Ismail, H Husain Jurnal Teknologi 76 (6), 2015 | 2 | 2015 |
| Multi-objective optimization in wire-electrical discharge machining (WEDM) of titanium alloy JB Saedon, N Jaafar, NHM Nor, MA Yahaya, H Husain Jurnal Teknologi 76 (6), 2015 | 2 | 2015 |
| A study on kerf and material removal rate in wire electricaldischarge machining of Ti-6Al-4V: multi-objectives optimization JB Saedon, N Jaafar, MA Yahaya, NHM Nor, H Husain 2014 2nd International Conference on Technology, Informatics, Management …, 2014 | 2 | 2014 |
| Optimizing Sintering Process to Produce Highest Density of Porous Ti-6Al-4V NHM Nor, MH Ismail, H Husain, J Saedon, MA Yahaya JOURNAL OF MECHANICAL ENGINEERING 5, 44-55, 2018 | 1 | 2018 |
| Muscular Activities Measurements of Forward Lean and Upright Sitting Motorcycling Postures via Surface Electromyography (sEMG) MIN Ma’arof, AR Omar, R Haron, H Husain, MA Wahab MATEC Web of Conferences 135, 00046, 2017 | 1 | 2017 |
| A comparative study of various binarization schemes for flame-front detection in a SI engine S Shawal, J Saedon, MS Meon, NH Mohamad, H Husain, M Mahat, ... IOP Conference Series: Materials Science and Engineering 834 (1), 012027, 2020 | | 2020 |
| Capability analysis of Puck damage model in predicting the damage behavior of unidirectional composite laminates under different scenarios MS Meon, H Husain, JB Saedon, S Shawal, NHM Nor, MN Rao, ... IOP Conference Series: Materials Science and Engineering 834 (1), 012028, 2020 | | 2020 |
| Thermal pyrolysis optimization for highest density of Ti-6Al-4V mix with Palm Stearin and Polyethylene NHM Nor, N Muhamad, H Husain, S Shawal, MS Meon, M Fauzi, ... IOP Conference Series: Materials Science and Engineering 788 (1), 012040, 2020 | | 2020 |
| Characterisation of recycled aluminium swarf into fine powder for MIM applications via ball milling SB Yussoff, NHM Nor, H Husain, S Alam | | 2019 |
| Debinding Optimization of Ti-6Al-4V Mix with Palm Stearin Binder NHM Nor, H Husain, S Shawal | | 2018 |
| of the Integrity Analysis of O&G Standpipe Separator: Numerical Study Article MFH Hidzir, KI Sainan, H Husain International Journal of Engineering & Technology 7 (4.27), 73-77, 2018 | | 2018 |
| Modelling Kerf Width in WEDM Titanium Alloy Using Response Surface Methodology JB Saedon, N Jaafar, MA Yahaya, NH Mohamad Nor, H Husain Key Engineering Materials 737, 83-89, 2017 | | 2017 |
| MODELING OF ALKALI-SILICA REACTION IN A TWO-PHASED MATERIAL MODEL Z Itam, H Husain Jurnal Teknologi 76 (9), 2015 | | 2015 |
