Seguir
Aitzol Lamikiz
Aitzol Lamikiz
Catedrático de Universidad del Departamento de Ingeniería Mecánica de la Universidad del País Vasco
Dirección de correo verificada de ehu.eus - Página principal
Título
Citado por
Citado por
Año
Machine tools for high performance machining
NL de Lacalle, AL Mentxaka
Springer Science & Business Media, 2008
331*2008
Laser polishing of parts built up by selective laser sintering
A Lamikiz, JA Sánchez, LNL de Lacalle, JL Arana
International Journal of Machine Tools and Manufacture 47 (12-13), 2040-2050, 2007
2622007
Experimental and numerical investigation of the effect of spray cutting fluids in high speed milling
LNL De Lacalle, C Angulo, A Lamikiz, JA Sanchez
Journal of Materials Processing Technology 172 (1), 11-15, 2006
2442006
Surface improvement of shafts by the deep ball-burnishing technique
A Rodríguez, LNL de Lacalle, A Celaya, A Lamikiz, J Albizuri
Surface and Coatings Technology 206 (11-12), 2817-2824, 2012
2292012
Cutting force estimation in sculptured surface milling
AD Lamikiz, LNL De Lacalle, JA Sanchez, MA Salgado
International Journal of Machine Tools and Manufacture 44 (14), 1511-1526, 2004
2062004
Evaluation of the mechanical properties of Inconel 718 components built by laser cladding
I Tabernero, A Lamikiz, S Martínez, E Ukar, J Figueras
International Journal of Machine Tools and Manufacture 51 (6), 465-470, 2011
1852011
Toolpath selection based on the minimum deflection cutting forces in the programming of complex surfaces milling
LNL De Lacalle, A Lamikiz, JA Sanchez, MA Salgado
International Journal of Machine Tools and Manufacture 47 (2), 388-400, 2007
1772007
Laser polishing of tool steel with CO2 laser and high-power diode laser
E Ukar, A Lamikiz, LNL de Lacalle, D Del Pozo, JL Arana
International Journal of machine tools and manufacture 50 (1), 115-125, 2010
1492010
Numerical simulation and experimental validation of powder flux distribution in coaxial laser cladding
I Tabernero, A Lamikiz, E Ukar, LNL De Lacalle, C Angulo, G Urbikain
Journal of Materials Processing Technology 210 (15), 2125-2134, 2010
1462010
Quality improvement of ball-end milled sculptured surfaces by ball burnishing
LNL De Lacalle, A Lamikiz, J Muñoa, JA Sánchez
International Journal of Machine Tools and Manufacture 45 (15), 1659-1668, 2005
1462005
Evaluation of the stiffness chain on the deflection of end-mills under cutting forces
MA Salgado, LNL De Lacalle, A Lamikiz, J Muñoa, JA Sánchez
International Journal of Machine Tools and Manufacture 45 (6), 727-739, 2005
1422005
CO2 laser cutting of advanced high strength steels (AHSS)
A Lamikiz, LNL de Lacalle, JA Sanchez, D Del Pozo, JM Etayo, JM Lopez
Applied surface science 242 (3-4), 362-368, 2005
1322005
On the influence of cutting speed limitation on the accuracy of wire-EDM corner-cutting
JA Sanchez, JL Rodil, A Herrero, LNL De Lacalle, A Lamikiz
Journal of materials processing technology 182 (1-3), 574-579, 2007
1252007
The effect of ball burnishing on heat-treated steel and Inconel 718 milled surfaces
LN López de Lacalle, A Lamikiz, JA Sánchez, JL Arana
The International Journal of Advanced Manufacturing Technology 32 (9), 958-968, 2007
1172007
Error budget and stiffness chain assessment in a micromilling machine equipped with tools less than 0.3 mm in diameter
L Uriarte, A Herrero, M Zatarain, G Santiso, LNL de Lacalle, A Lamikiz, ...
Precision engineering 31 (1), 1-12, 2007
1172007
Plasma assisted milling of heat-resistant superalloys
LN Lo´ pez de Lacalle, JA Sa´ nchez, A Lamikiz, A Celaya
J. Manuf. Sci. Eng. 126 (2), 274-285, 2004
1172004
Modelling of energy attenuation due to powder flow-laser beam interaction during laser cladding process
I Tabernero, A Lamikiz, S Martínez, E Ukar, LNL De Lacalle
Journal of materials processing technology 212 (2), 516-522, 2012
1152012
The milling of airframe components with low rigidity: a general approach to avoid static and dynamic problems
S Herranz, FJ Campa, LNL De Lacalle, A Rivero, A Lamikiz, E Ukar, ...
Proceedings of the Institution of Mechanical Engineers, Part B: Journal of …, 2005
1112005
Model for surface topography prediction in peripheral milling considering tool vibration
M Arizmendi, FJ Campa, J Fernández, LNL De Lacalle, A Gil, E Bilbao, ...
CIRP annals 58 (1), 93-96, 2009
1082009
The Denavit and Hartenberg approach applied to evaluate the consequences in the tool tip position of geometrical errors in five-axis milling centres
A Lamikiz, LN López de Lacalle, O Ocerin, D Díez, E Maidagan
The International Journal of Advanced Manufacturing Technology 37 (1), 122-139, 2008
1062008
El sistema no puede realizar la operación en estos momentos. Inténtalo de nuevo más tarde.
Artículos 1–20